You can get your devices MEID into the system by one of two ways .... either contact someone such as a dealer to get it into the system (craigslist is your friend), or change / repair the MEID on your HTC Evo to match the MEID of your MetroPCS device.
2.Open Dialpad and Dial ##3424# or The Diagnostic Menu Code For Your Specific Device
3.Make sure that you have an SD Card inside your phone
Download and install SPC Utility on your android device
SPC Utility
Download QPST or CDMA Workshop 2.7
This Tutorial Will Be Using QPST Which can Be Downloaded From the Link Below
QPST 2.7.323
4. Install HTC Diag Drivers or Corresponding Drivers From Our Download Page
Link For Download Found Below
HTC Diag Drivers
5. Plug In Your Device and Drivers Will Automatically Install
6. Open QPST
7. Click on add new port
8. Uncheck the box that says "Show Serial..."
9.It should look something close to this after the port is added
10.Go To Start Clients Menu and Click "Service Programming"
11.The below box will come up with the port you just added just hit ok
12. The next window will look something like this
13.Click "Read" it will ask you for your SPC Code (You can find this by running the SPC Utility that you installed earlier)
Most Verizon Devices or Pre-Flashed Devices will be 000000
14. Once the contents of your device have been read there will be a box on that same screen that has "SPC Change" next to it ... if your SPC Code is anything OTHER THAN 000000, Check this box and fill in 0's
DO NOT HIT WRITE YET ... We Have Alot of Other Settings to Change
15. Go to the roam tab hit browse and choose a MetroPRL
If You Do Not Have one I Have a Link Below
Download Metro PRL Here
16.Now go to the MIP tab inside of QPST ... Copy all the settings from the bottom portion of my picture below onto the settings of your phone. BE SURE TO SET MOBILE IP BEHAVIOR TO "SIMPLE IP ONLY" without changing this your device WILL NOT get 3G where available it will always be 1x and we don't want that
17. Now Click Profile 0 and hit edit. Copy all the settings from my picture below. In NAI and Tethered NAI type (Your10DigitPhone#)@mymetropcs.com .... For Example [email protected] ..... In HA and AAA Shared Password you will enter your MetroPCS MSL Code ... THIS IS NOT 000000 ....
To get our HA and AAA Passcode we will use our MetroPCS MSL Code Calculator ... Download Link Below
Metro MSL Code Calculator Download
Now to get our 6 Digit Password ... if you paid someone to add your MEID into MetroPCS system you will simply type in the MEID from your phones settings into the calculator and get your MetroPCS MSL .... IF YOU HAVE USED A DONOR PHONE TO CLONE THE MEID FROM YOU WILL PUT THE METROPCS TELEPHONE THAT YOU USED MEID INTO THE PROGRAM .... This is Important ... This is Your 3G internet access password ... the words metropcs only allow you to get 1x...
18. Now do the same thing for profile 1 ... Picture Below
19 Now go to the PPP tab and copy all the settings I have in my picture below
20. Stay inside the PPP tab and go to the "UM" Section .. and copy my settings once again in my picture below
For Tethered NAI and User ID type in your (10digitPhone#)@mymetropcs.com that you used earlier and for your password you will use your MSL code that we calculated earlier.
21.Once you're finished with the UM section go to the "AN" Section and copy my settings from below one last time ( Picture Below )
This Time you cant enter anything in the Tethered NAI but in USER ID enter once again (your10digitphone#)@mymetropcs.com and the same MSL password you used that we calculated earlier.
22. Once You're Finished Hit Write ..... if you get an error just ignore it ... your phone should reboot automatically .. if it does NOT ... reboot it manually then enjoy your 3G internet :) ....
If you found this helpful please donate $5 Below it's not much but will support on-going research and development to keeping this website up to date with the LATEST information to help you with ALL your needs